What’s already on the market To get a wide range of options I had to do quite a lot of researching online and in the local hardware did stores such as woodiest and other shops such as Argos and Nava furniture. Below are some of the designs that I was very impress with it but could not pick it because it did not fit in to my aims of what the project should look like. The reason on very idea is outlined to why I liked it and why I did not approve it. This is another great simple coffee table that will look good with the existing furniture.
It is also doing more with less so it is a very good idea. My choice: the reason why I selected this idea was cause it fills all the aims I set out at the start of my investigation/research. This idea serves the comment doing more with less perfectly because it does not require too much wood or expense as it would if I was to make a coffee table and drawers alone so its doing more with less because they are together. It is also something that will free up a lot of space up in the room.
Possible wood types oak the advantages of Oak are: Oak wood has great strength and hardness It is very resistant to insect and fungal attack It is easy to cut It also looks good It is a very strong wood and resistant to many pests and to rot Beech Advantages of beech wood furniture are: hard materials, textures, the structure is fine wear-resistant and shiny processing, finishing, gluing is better The disadvantage of beech wood furniture is: color and density differences due to age different, makes furniture color is not uniform; kiln drying and processing that is easy to crack and easy to shape.
PINE Advantages of pine are : Fairly cheap and readily available. Easy to work and finishes well. Durable. Disadvantage is that it can be Knotty Dovetail Dovetails are the strongest of all Joints. The joint is made up of interlocking wedge-shaped elements called pins and tails that resist the forces applied to the Joint. This Joint looks attractive and, if well made, the decorative quality can be used to enhance projects. Advantages of Dovetail Joints What are the advantages of this type of Joint? Strongest of all Joints. Large gluing area. Interlocking Resists being pulled apart.
Looks attractive. Would hold together even with no glue. Mortise & Tendon Joint This Joint is a strong and frequently-used joint for assembling a variety of products where strength and reliability are required. The mortise can either be a through mortise, s shown, or a blind mortise that only partly penetrates the stock. The Joint is made permanent using adhesive. Dowels are also used to prevent separation. Lap Joint Another simple Joint is the half-lap Joint. This requires the removal of stock to exactly half of the overall thickness of the piece, in order that a similar piece can mate with it.
This technique is also used in the cross-halving joint. Cross halving – Lap Joint The main uses for this Joint are to allow two pieces of stock to cross such that the Joint is contained within the overall thickness of the material. Used for structural frames. Glue lone can be used as a fixing method, or combined with screws or nails. Finger Joint This Joint is a positive permanent strong Joint when fixed using adhesive. The long length of glued area is very beneficial to the resulting strength. The in-line version is often used to produce a long length of timber / glued laminate from shorter lengths.
The corner version is used for producing strong drawers boxes etc. The Joint if made even stronger if the fingers are made using dovetail form Chipboard is an artificial wood made like MAD but from actual wood chips, hence the name. It is widely used for the structural assign of kitchen furniture and cabinets which are then covered with a laminate or wood veneer. It is also widely used for low cost sub flooring. It is only useful in sheet form and cannot be easily used or worked in any other format.
Elm is valued for its interlocking grain which gives it a high resistance to splitting, with significant uses in chair seats and coffins. Elm wood is also it quite pliant and is available in long planks due to the long, straight, trunks of the tree, For these reasons elm is favored as a source of timber for keels in ship construction. Elm was historically used by bowers during the Middle Ages to make longbows. Mahogany is finely grained hard wood which is reddish brown color. It is extremely durable and resists swelling, shrinking, warping and twisting.
Mahogany is used extensively for high quality, expensive furniture such as wooden cabinets and veneered tables and dressers. It is also used in the construction of boats due to its high resistance to swelling and warping caused by water Plywood is an artificial wood that was invented during the Second World War and was primarily used to build boats and landing craft for the military. It is made from numerous thin laminates of wood glued gather. Each layer is at right angle to the grain of the other to give it great strength while also allowing it to remain quite pliable.
Tempering puts the outer surfaces into compression and the inner surfaces into tension. ) choosing the type of wood to use When it comes to choosing the best wood coffee table, the choice comes down to a few basic considerations: type of wood, size, features, and aesthetics. The decision I came up with early on was to use natural real wood due to a few reasons that are: cheaper boards will chip and rot unlike real solid wood real solid wood looks much better than cheap chip boards real solid wood normally age well so it is worth the investment because it will last